DSL-1504G Bridge Mode

DSL-1504G Bridge Mode Quick Setup

1.1 Configure DSL-1504G CO

   (1) Open IE browser, enter https://192.168.0.1, click “Yes” continue.

(2) Enter user name “root” and password “admin”, click “OK” into configuration page

(3) lan configuration  (Basic configuration-LAN-configuration)

(4) setup atm channel ( Basic configuration – WAN-ATM Channel)

(5) Click “Create New Channel”

(6) Encapsulation is RFC2684-bridged, click “Apply”

(7) Setup DSL (Basic configuration - DSL)

 setup   “Service Type” is “CO/2wires”

 Click “Apply”

(8) Setup Bridge Interface

Click “Create New BVI”

 

Click“Apply”

 Click “Bridge Index” bellow’s number

Click “Available member to add to bridge” -“lan(+)”,click “OK” continue

Click “Available member to add to bridge” -“atmVc1(+)”

Save configuration (Admin-Save Configuration)

DIR 600L Reset Issue Fix

Follow the instruction given below given to fix the resetting problem on your D'Link DIR-600l (hw: b1) :

• Click Download to get your update file.
• Connect to your dlink router via wired lan cable
• Open the gui(default : 192.168.0.1)
• Click Maintenance > Firmware > Browse the firmware file and upload.

After successful upload, power cycled your device and reconfigure your isp settings to connect to the internet.

DSL-2730U Device Hang Issue Fix (TR-069)

This is a fix to the issue faced by D'Link DSL-2730U where the router suddenly stops responding and all the led's are stable. 

The temporary solution to this is to power cycle your DSL-2730U. But we have a permanent solution to the following problem on the device. Please follow the instructions give below to resolve the issue :

• Login into the gui of the device
• Username : admin
• Password : admin / leave the password field blank
• Click Advanced tab > Network Tools > TR-069

ACS configuration, change the settings as below :

• Uncheck the checkbox next to enable
• Change the url to http://acs.dlink.com
• Select Periodic Table Inform Enabled : DISABLED

Change the connection request settings as shown below :

• Username : D-link
• Password : D-link1234
• Path : /tr069
• Port : 7547

Click on the Apply Change button located at the bottom of DEBUG, as shown in below :

Incase the same issue occurs again your DSL-2730U, please visit the service centre and get your device checked. Dlink also provides door-door service. Call 1800-233-0000 for immediate assistance on the same.

How to configure DSL-2750U as an access point

The following is the procedure to configure your Dlink DSL-2750  as an access point :

• log into the gui (default ip : 192.168.1.1 )
• click wireless > manual wireless connection setup
• give your wireless a network name
• select security mode as WPA
• save setting.
• click setup > lan setup/network settings
• disabled dhcp server
• save settings
• change the router ip address in your network range
• save settings
• power off the DSL-2750U
• connect a lan cable in one of the four lan port from your  main router

• power on and wait for 60 seconds 
• check your connectivity

Unable to LAN devices from wireless devices on DSL-2750U

Have you come across a scenario where your laptop connected over wireless is unable to ping your desktop pc connected with a wired cable to the same router? If yes is your answer, we have a solution to this.

This fix applicable for all DSL-2750u & DSL-2730U.
Please follow the instructions given below to fix the issue :

• log into the the gui(default : 192.168.1.1)
• click setup > wireless > uncheck mult-ap isolation or clients isolation
• save setting and reboot your router.
• test your ping response

D'Link DIR-605L Reset Issue Fix

Follow the instruction given below given to fix the resetting problem on your D'Link DIR-605l :

• Click download to get your update file.
• Connect to your dlink router via wired lan cable
• Open the gui(default : 192.168.0.1)
• Click Maintenance > Firmware > Browse the firmware file and upload.
• After successful upload, power cycled your device and reconfigure your isp settings to connect to the internet.

How to configure a dlink cloud camera

Dlink has a wide range of network cameras which offers quick setup to its users.

Please follow the instructions given below to configure any D'Link Cloud Camera :

• Visit https://in.mydlink.com/entrance 
  
• Click the Support Tab> Select your cloud camera 
• Download the setup wizard below as per your OS and device hardware version
• Reset your camera before running the setup wizard
• Connect your dlink camera via lan cable to your router
• run the setup wizard on your computer which is also connected to the same router(wired/wireless)
• Follow the instructions on the setup wizard to configure your camera step by step

Dlink DIR - 816 Reset Issue Fix

Follow the instruction given below given to fix the resetting problem on your D'Link DIR-816 :

• Click  download to get the update file and save it in your system 
• Connect to your dlink router via wired lan cable
• Open the gui(default : 192.168.0.1)
• Click Maintenance > Firmware > Browse the firmware file and upload.
• After successful upload, power cycled your device and reconfigure your isp settings to connect to the internet.

Whatsapp Hack

Ever thought of hacking into somebody else's whatsapp account? Yes, then the hack is right here.

Although it is unethical to get into somebody's account and exploit their privacy, I am writing this blog for educational purpose only. 



Follow these steps to get access to whatsapp account on your phone :

• Download & Install Whatscan, an android app available on google play and install it in your phone.
• Now, this is where you need to be careful, get access of the persons phone you want to hack into and follow these steps :

1. Open Whatsapp
2. Click Whatsapp Web
3. Now, Open Whatscan on your phone
4. Scan the QR CODE from the Whatsapp Phone that you wish to hack into.
5. Enjoy Unlimited Access

Note : You have unlimited access the whatsapp account until the user logs out from all computer on whatsapp web.  You can send messages as well.

Tips secure your home wifi

Here are few tips to secure your home wifi from being hacked by unwanted users. Follow the instructions given below to secure your home wireless network :

• Secure your wireless network with WPA encryption : Securing your network with a password is a necessary step we all follow to protect our home wifi service being used by unknown users. WPA & WPA2 are termed as one of the strongest and most secured password encryptions available to us.
• Disable WPS : WPS stands for wifi-protected setup, a feature available on our wireless to connect wps enabled devices which user a WPS button located on the router or by using the WPS pin.
• Enable Mac Filtering and allow only your devices in the list : This is an advanced security feature you can use to block unwanted devices to connect to your home network and user your service. You can create two types of lists i.e either allow a list of specific devices to connect to your network or block a list of devices. The features requires the mac address of all the devices you wish to block or allow in your network.
• Setup a password to login into the gui of your router : This is also one of the important aspects while you are on a quest to secure your home network. All your configurations are being set on this web gui of the router and hence the access to this interface should be limited to only you and your other administrators. 

Caution : In Case your forget your admin credentials to login into the gui, you will than have to hard reset the router and reconfigure it again to connect to the internet.

• Enable hidden broadcast of your wireless network : The visibility of your wireless network is in your hands. Feel free the decide on making your wireless network visible to other or not. Hiding your wireless network name will also add a step in securing your home network.

Frequent disconnections over the wireless network Fix

We often come across this problem of disconnection over wireless network at times.

The following are the reasons behind the issue :

• interference caused due to other electronic devices (eg: microwave oven; cordless phones)
• interference caused due to other wireless router around its area.

The following is the fix for the disconnections. please follow the instructions given below to resolve your issue :

• log into the web gui of your router
• go to the wireless settings> select the wireless channel (1 / 6 / 11 )
• save settings & reboot your device
• monitor the connection
• select the best channel for your network after monitoring.

DSL-2750U Configuration

DSL2750 - Configuration

DSL-2750u is adsl modem + wireless router by D'Link specifically designed for adsl connections. 

Please follow the instructions given below to start configuring your dlink router :

• connect your dsl line into the dsl port of the device
• connect your laptop/pc over the wireless to the dlink router
• after the above connections are made, please check the led lights on your DSL-2750U

Make sure the following led's are on :

- POWER : ON (green);

- LAN : ON (green);

- WIFI : ON (green);

- DSL : ON (stable green);

• open a web browser
• type 192.168.1.1 in the address bar and hit ENTER
• enter username as 'admin' and password as admin or else leave the password field blank > Press login.
• After logging in the web configuration page, the Wizard page appears as shown on the right. The Wizard page will guide you to fast configure your router to connect the Internet. Click Setup Wizard. 
• In the next page shown on the right, there are 5 steps to configure the device. Click Next to continue. 
• Set the time and date, and then click Next. 
• Configure the Internet connection. We set the parameters of this page based on PPPoE protocol as example.

 1)  Select PPPoE in Protocol.

 2)  Enter the VPI and VCI provided by your ISP. 

 3)  Enter the Username and Password provided by your ISP.

 4)  Re-enter the password for confirmation. 

  5)  Next

Note : Different protocol requires entering different information. You can fill in the entries according to what your ISP provides you. 

• Configure the wireless network in next page. 

1)  Check Enable Your Wireless Network.

2)  Set the SSID for your wireless network, you can also keep it as default.

3)  Choose to display or hide your wireless network. - Visible: Your wireless network can be detected. - Invisible: You wireless network cannot be detected. Wireless clients needs to enter the SSID and password manually to join this wireless network.

4)  Set the security level. The default security level of wireless network is None. Choose an encryption mode for the wireless network. It is recommended to choose WPA2-PSK.

5)  Enter a new password in WPA2 Pre-Shared Key.

6)  Click Next to go to the next page. 

• Set a new login password. If you want to keep the previous password, click Skip to go to next page directly. After setting a new password, click Next. 

 Note: The login password cannot contain a space. 

• View the setup summary.  Click Apply to take the setup into effect.  Click Back to modify the setup. Click Cancel to cancel the whole setup. 

DSL Blinking fix for D'Link DSL-2750U

DSL Blinking fix for D'Link DSL-2750U

DSL led blinking is one of the common reason for internet disconnections for adsl type of ISP connections. Usually this happens whenever there is some kind of interference or disturbance in the dsl line. Too many joints left open or faulty splitter is also one of the reasons for DSL blinking.

Before you go ahead and customize your dlink adsl router, please check on the following things :

• - make sure there is no disturbance in your telephone line
• - check your dsl cable
• - check if the dsl led gets stable bypassing the splitter

If the above mentioned steps do not help, please follow the instructions given below on to fix dsl led blinking on your DSL-2750U (fw version : 1.0IN)

• - Log into the gui of the device (default : 192.168.1.1 )
• - username : admin
• - password : (blank) or admin
• - Click Advance tab > Network Tools > Adsl
• - Adsl Modulation > Select Multimode 
• - uncheck all these options(g.dmt;  glite; g.imp; T1.413; AnnexL;  AnnexM;)
• - check mark only on ADSL2+
• - Save settings & reboot done
• - Give your router 2-3 minutes and your dsl led will stabelize.

Note : Incase the dsl blinking issue does not resolve, please contact your ISP and file a complaint. Verify your dsl line and its connectivity with a test modem.